Join for FREE
It only takes a minute!
Zeiss - Always on the lookout for something special – Shop now

Welcome to BirdForum.
BirdForum is the net's largest birding community, dedicated to wild birds and birding, and is absolutely FREE! You are most welcome to register for an account, which allows you to take part in lively discussions in the forum, post your pictures in the gallery and more.

Lens hood problem of ATS with SOCase in place.

Reply
 
Thread Tools Rate Thread
Old Saturday 29th December 2018, 22:10   #1
Crake Dude
Registered User
 
Crake Dude's Avatar

 
Join Date: May 2006
Location: Derbyshire, UK
Posts: 186
Lens hood problem of ATS with SOCase in place.

Am I living in a parallel universe...or is it just me, or what!

A few weeks ago I thought I'd treat my Swaro ATS80 HD to a new Swaro stay-on-case(SOC) because mine was looking a bit tatty, and the photos of the later design with black trim looked very 'pwetty'. Also, I was tired of having to partly unzip the body case to enable the lenshood to slide in and out, very poor design fault, IMO.....surely this had been corrected in the newer design. Case arrived, I fitted it on and....nope, same problem, lenshood almost impossible to slide out with SOC in place. It's even worse now that the body case zip is divided into two, instead of the all-around zip on the older SOC, and the zips start at the object lens end so cannot be partly unzipped to reduce friction with the SOC and scope's body.

I contacted Swarovski customer service and part of their response was, 'As the SOCs are sewn by hand, sometimes the cases are a bit too tight. Nevertheless, you should definitely be able to extend the lens hood.' I definitely cannot without great effort, and expletives abounding from my mouth.

After much thought, I seem to have found the solution, though it's highly technical and very expensive, but that's no problem for us/you have-to-be-filthy-rich to be Swaro owners, is it. Here goes:

I could feel that the lenshood very gently 'snapped' into position when in the fully retracted position. Even though there are indentations in the SOC to enable a better grip to pull the hood out, it's that final snapping back which was the main cause, I reckoned. So, with the SOC off, I just put a rubber band in the gap formed between the rear of the hood and the scope body if you slide the hood forwards a few millimetres. SOC back on, much easier now to slide the hood out, especially if you use a twisting action. Sorry to be all technical.

So, are Swaro gonna include 3mm rubber bands now with their SOCases, or sell 'em separately....which do you think.

Good luck.

Steve
Crake Dude is offline  
Reply With Quote
Old Sunday 30th December 2018, 11:36   #2
Binastro
Registered User

 
Join Date: Aug 2012
Location: S.England
Posts: 4,445
The postman here leaves a steady trail of suitable rubber bands in two sizes.
Normal and Swarovski lens hood size.

The advantage of these is that they always seem to be fresh, and if an old in use one is perished, fresh ones seem to be always available.
Binastro is offline  
Reply With Quote
Old Sunday 30th December 2018, 21:09   #3
seawatcher
Registered User

 
Join Date: Feb 2004
Location: no fixed abode
Posts: 120
I also experienced the same problem and remedied with a piece of 3 mm thick string, which should last longer than a rubber band. In fact it has been in place for 3 years now :-)
seawatcher is offline  
Reply With Quote
Old Monday 31st December 2018, 12:43   #4
bioscope
Registered User

 
Join Date: Nov 2016
Location: Germany - Hessen
Posts: 71
I think it is normal, that there are some 'problems' with the lens-hood. At the time my Zeiss DiaScope was new (2011), the SOC (also two parts) were very tight. My dealer told me, that there is some time needed to use the SOC normally - that was true, 4-5 weeks later all functions (e.g. pulling out the hood) worked well. Since 2011 there was no flaws with the scope and the SOC (original Zeiss), but I bought two hoods from heliopan (2x5cm - aluminium) because the retractable hood(s) are very short. You can see this better behaviour whlie digicoping with lower sun in the direction of the objective.

good pulling
Manfred
bioscope is offline  
Reply With Quote
Advertisement
Reply


Thread Tools
Rate This Thread
Rate This Thread:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is Off
HTML code is Off

Similar Threads
Thread Thread Starter Forum Replies Last Post
150-500 Lens Hood Andy Benson Sigma & Other Third Party Lenses 4 Monday 7th May 2012 09:15
Lens hood for Sigma lens. stevo Sigma & Other Third Party Lenses 1 Thursday 1st January 2009 20:00
Lens Hood Problem Canon F/5.6 L 400mm Cudyll Bach Canon 6 Monday 11th February 2008 10:27
Lens hood problem DJRWhittle Cameras And Photography 3 Sunday 30th September 2007 20:41
viewing hood attached to CP4500 problem!!! breffni Nikon 0 Thursday 22nd September 2005 15:25

{googleads}

Fatbirder's Top 1000 Birding Websites

Help support BirdForum

Page generated in 0.21564388 seconds with 16 queries
All times are GMT. The time now is 04:29.